Fillet weld vs groove weld: meaning and how to check it

A fillet weld is a roughly triangular weld laid in the corner where two surfaces meet at about a right angle, with no edge preparation needed. A groove weld is made in a groove between the members, usually cut or shaped first, and is sized by how deep it reaches into the joint.

Two T-joints drawn end on. A: an upright plate on a base plate with a triangular fillet weld in each corner and neither edge cut. B: the same upright plate with its lower edge beveled on one side, the bevel filled by a groove weld and a lighter reinforcing fillet over it
Same joint both times. The edge prep and the weld are what change.
Use this diagram

How to tell a fillet weld from a groove weld

  1. Look at the edges. If neither member was cut and the weld sits in the corner, it's a fillet. If an edge was beveled, J-shaped or set with a gap, and the weld fills the space between the members, it's a groove weld.
  2. Look at the section. A fillet sits outside the members, in the corner they form. A groove weld sits inside the joint thickness, between the members, with any reinforcement standing proud of the surface.
  3. Read the symbol. The fillet symbol is a triangle with the leg size on its left. Groove symbols draw the edge prep instead: two strokes for a square groove, then a V, a bevel, a U or a J. On a groove symbol the left side carries the groove depth and, in parentheses, the weld size.
  4. Name the joint separately. A T-joint can take fillets, a groove weld or both. A butt joint has no corner for a fillet, so it takes a groove weld, square or prepared.

How each one is sized and checked

A fillet is sized by its legs, measured from the joint root along each member to the toe. You check the legs, and convexity or concavity, with a fillet gauge on the finished weld. The throat that carries load sits inside the triangle and is worked out, not measured.

A groove weld is sized by its depth into the joint. That makes it either CJP or PJP: through the whole thickness, or part way by design. You can't see that depth from the face of a finished weld, so the checks come earlier and later. Before welding, you check the bevel, the root face and the root opening against the WPS. After welding, you check the reinforcement height and the toes, look at the back where you can reach it, and leave hidden depth to radiography, ultrasonic testing or a cut section where the contract asks for one.

Try one question

Question 1 of the free 10-question check on CWI Part A. No signup. Then ask Tack, the AI study assistant, why the answer is right and the others are wrong.

Question 1 of 10 · free checkUntimed

Definitions and Terminology

A fatigue crack in a cyclically loaded fillet-welded attachment started along the line where the surface of the weld blends into the flange plate. At which weld feature did the crack start?

Press A-D or 1-4 to choose an answer while this question is on screen.

Choose an answer to begin

Common mix-ups

  • Joint versus weld. T, butt, corner, lap and edge name how the members meet. Fillet and groove name the weld that joins them. Name the joint first, then read the weld.
  • Groove welds only in butt joints. No. A T-joint or a corner joint can be beveled and groove welded, often with a reinforcing fillet over the groove, as in the drawing.
  • Leg versus throat. On a fillet, the leg is what your gauge reads. The throat, the shortest path from root to face, is what the strength depends on.
  • Reinforcement versus convexity. Extra metal above the plate surface on a groove weld is reinforcement. Extra metal on a fillet face is convexity. Same idea, different words.
  • Which is better. Neither, in general. A fillet needs no edge prep and is quick to make. A groove weld costs prep and often more weld metal, and it can carry load through the full thickness of the member. The drawing or WPS picks the weld, and the inspector checks that what was built matches.

Fillet and groove welds on the CWI exam

AWS lists joint design and welding symbols among the subjects the Part A Fundamentals exam tests. Definitions and Terminology is at least 12% of the closed-book Part A, and Symbols, Welding and NDE at least 10%. Expect to name the weld from a sketch and tell a fillet symbol from a groove symbol at a glance.

On Part B, AWS lists a plastic replica set with a sample T-joint and a sample groove weld, and a tool kit with fillet weld gauges and a V-WAC gauge. Welding Inspection and Discontinuities is at least 34% of the practical, so knowing which gauge fits which weld saves time.

Practice it

The CWI Part A flashcards drill weld and joint terms and symbols with original cards. Fillet legs, throats and the fit-up terms for groove welds each have a row in the welding terms glossary.

Name the weld on sight? Check the rest of Part A

Take the free 10-question check. It's weighted to the Part A outline, scored by domain and needs no signup, so you see which domain costs you the most points. The Part A course then gives you a lesson on every exam subject, two full-length timed practice exams, and a worked explanation with every answer.

Sources

Show the list
Ask Tack: Am I ready?

Ask Tack before you buy AI your AI study assistant

See what's on the CWI Part A exam, test yourself with 5 quick questions, or find the plan that fits you.

The CWI Part A course

Available now · instant access

Learn every Part A topic, then prove it on timed practice exams.

Part A course$99Get the Part A course · $99

Instant access. Terms and refunds · Secure checkout by Stripe · Billed by Nori Software

What's inside
  • 10modules of lessonsEvery task on the outline
  • 2full-length timed exams165 questions in 135 minutes each
  • 720practice questionsEach one explained
  • 5worked calculationsStep by step
  • 1week-by-week study planSet to your exam date

Turn a practice answer into a study step. In untimed practice, ask Tack AI about any question you answer, follow up, then see your weakest topics and what to drill next.

Every answer comes with a full explanation.

Fillet Gauge editorial team

Facts come from the sources listed above. If something has changed, tell us and we will correct it.

Your next step

Ready to see where you stand on CWI Part A?

Free, untimed and scored by domain. No signup.

Free 10-question check

Part A course. Lessons, timed practice exams and a plan around your exam date.

Get Part A course · $99

Want a timed run? Take the free 25-question practice test (about 20 minutes). No email needed.

Prefer paper? Free printables

From the blog

All 21 related guides